Nick's appliance repair
🔥 DON'T MISS OUT! LIMITED TIME OFFER: ONLY NOW - SERVICE CALL JUST $89! 🔥
By: Nick
By: Nick

CEO Nick's Appliance Repair

Whirlpool Oven Not Heating Up

Table of Contents

Whirlpool Oven Not Heating Up? Here’s How To Fix It

If you’re experiencing a problem with your Whirlpool oven not heating up, this comprehensive guide will assist you in identifying the root cause and providing the necessary solution. Begin by examining the first possible cause in the guide, then continue down the list until you’ve identified the specific cause and implemented the recommended solution.

Make sure the power is working.

When troubleshooting a gas or electric oven that’s not turning on, the first step is to ensure that the power supply is still working properly and correctly. Your oven requires a specific amount right voltage of alternating current to function properly, with electric ovens requiring 250 volts and gas ovens requiring 120 volts. If the power supply is inadequate, your oven won’t be able to turn on.

To check the power supply, begin by plugging the oven into a different socket than the one it’s normally connected to. If the oven works in the new socket, a qualified electrician must repair or replace the original socket. If the oven still doesn’t work, check the circuit breaker to ensure it has the correct voltage. If the circuit breaker is faulty, it will need to be repaired or replaced.

Suppose the socket and circuit breaker function correctly, and your Whirlpool oven still won’t turn on. In that case, you’ll need to have an electrician inspect all the wiring of the whirlpool oven model to diagnose and resolve the issue.

Check the gas supply.

Once the power supply or electrical outlet has been ruled out as the cause, the next step is to examine the gas supply. However, if you have an electric oven, you can proceed directly to the local gas supplier to step 5. Here’s what you need to do to inspect the gas supply:

First, ensure the oven safety valve or gas cutoff valve is turned on. If it’s not, switch it on. Then, ensure that all other safety and gas valves within your system are switched on. If any of them are off, turn them on.

Next, attempt to turn on the range burner of your oven and check for any gas odors emanating from it. If you detect a gas smell, the oven’s gas supply works correctly, and you can move on to step 3.

If there is no gas smell, use a multimeter to check the valves (if they’re electronic) to determine if they have continuity. If any of the valves are malfunctioning, replace them. If they’re not defective, you’ll need to enlist the services of a qualified technician to inspect your gas and electrical supply and lines.

Make sure the igniter is working.

The next step in troubleshooting your Whirlpool oven is to examine the gas oven racks igniter to ensure it functions correctly. The oven door igniter is responsible for lighting the gas when you turn on the oven, and when it malfunctions, your oven won’t be able to heat up.

Here’s how to inspect the igniter:

First, locate the faulty igniter; it’s situated next to the burner. Then, attempt to turn your oven on. If the gas doesn’t ignite, use a multimeter to test the oven igniter itself (make sure you disconnect it first and turn off the gas and power). If the oven has a faulty igniter or doesn’t have continuity, replace it. If it does have continuity, reattach it to your oven and move on to step 4.

Once you’ve installed a new igniter into your Whirlpool oven, try turning the oven on and heating the igniter again. If it still does, the the oven igniter still won’t heat up, proceed to step 4

Make sure the broil spark electrode is working.

The spark electrode is another crucial element of your Whirlpool gas oven that aids in igniting the top bake burner or broil burner ignition flame, allowing the temperature inside the oven to heat up. If it ceases to function, your Whirlpool oven will not heat.

Here’s how to inspect the spark electrode:

First, turn off the power and gas supply. Then, locate the spark electrode and thoroughly check it for any signs of damage. If the spark electrode is damaged, it needs to be replaced. If it isn’t damaged, test the spark electrode using a multimeter (disconnect it first and keep the gas and power off). If the spark electrode doesn’t have continuity, replace it. If it does have continuity, reattach it to your oven and move on to step 6 (note that step 5 is for electric ovens only).

Once you’ve installed a new spark electrode in your electric oven or Whirlpool oven top, try turning the whirlpool oven won’t heat the flame on again. If it still doesn’t heat up, proceed to step 6 (remember, step 5 is for electric ovens only).

Make sure the bake element is working.

In a Whirlpool oven that runs on electricity, the heating element is responsible for providing heat and electricity to the heating elements in the oven. If this heating element malfunctions, your whirlpool ovens won’t heat properly.

Here are the steps to check the bake element:

Turn on your oven to the highest temperature.

After a few minutes, look at the element and check if it’s bright red. If it’s not, then it isn’t accurate and must be replaced. If it is, proceed to step 6.

To confirm that the element is faulty, disconnect it and test its temperature with a multimeter (make sure it’s cooled down before doing this test).

If the element lacks continuity, it needs to be replaced. If it does have continuity, move on to step 6.

Install the new heating element, and check if your Whirlpool bottom oven is heating properly. If it’s not, proceed to step 6.

Make sure the thermal fuse is working.

To ensure that your electric Whirlpool oven operates correctly, it’s essential to check the functionality of the temperature sensor and its thermal fuse. The purpose of this device is to monitor your whirlpool oven heat well’s temperature, and in the event of overheating, it sends a signal to the oven cavity main control board, which turns the oven off. However, in some cases, the thermal fuse can malfunction, resulting in the Whirlpool oven not heating or being unable to turn on.

To check the thermal fuse, follow these steps:

Turn off the power and gas supply.

Locate the thermal fuse in your oven.

After disconnecting it, use a multimeter to test the electrical current and incoming voltage from the thermal fuse.

If the thermal fuse lacks continuity, replace it. If it has continuity, move on to step 7.

Install the new thermal fuse test used in your Whirlpool oven.

Attempt to turn on the hot burner in the oven to verify if it heats up.

If the oven still fails to heat up, proceed to step 7.

Replace the control board.

If you’re facing issues with your Whirlpool oven control board not heating up, replacing the control board could be the final solution. However, testing the whirlpool oven, not the heating control board yourself, can be challenging, so it’s often best to replace it and hope for the best. Another option is to call a certified technician to examine your whirlpool oven model or consider buying a new one.

Conclusion

If your Whirlpool oven not heating up, there could be various reasons behind it. This comprehensive guide provides a step-by-step approach to identifying the root cause and fixing the issue. From checking the power supply, gas supply, igniter, broil element, bake element spark electrode, bake element, and thermal fuse, the guide covers all possible causes of the malfunctioning. Following the instructions carefully and taking all necessary safety precautions while working with electrical or gas components is essential. If you cannot identify and fix the issue, it’s always better to consult a qualified technician.

 

Frequently Asking Questions

 

Why is my oven working but not heating up?

This could be caused by a number of issues, such as a broken heating element, faulty thermostat, or clogged vents. You should check the oven control settings to make sure they are set correctly and also inspect the heating element for signs of damage or wear and tear. If you find any evidence of this, it’s best to replace the element with a new one. You should also check the thermostat for any signs of faulty wiring or other damage and replace it if necessary. Additionally, be sure to clean out any clogged vents that may be restricting air flow to the oven. This could be causing the oven to work but not heat up properly. Once all these steps have been taken, your oven should be heating up properly. If the issue persists after all of these steps, it might be a good idea to call in Nick’s appliance repair service for assistance.

Is there a reset button on a Whirlpool electric oven?

Yes, most Whirlpool electric ovens have a reset button located on the back panel. This is typically marked with the word “reset” or a similar phrase. To use it, simply press and hold the reset button for 5 seconds or until the oven display powers off and then back on again. This should initiate a reset of your oven and should hopefully fix any problems you’re experiencing. Also, you can unplug the oven for about 10 seconds and then plug it back in to reset it. However, if this does not work or the problem persists, you can contact us for assistance.

Why is my Whirlpool oven not heating to temp?

There are a few potential reasons why your Whirlpool oven is not heating to the right temperature. The first thing to check is that all of the controls are set correctly and then inspect the heating element for signs of damage or wear. If there is any damage, it’s advised to replace it with a new one. Additionally, be sure to check the oven thermostat for faulty wiring or damaged parts and replace it if necessary. Finally, you should clean out any clogged vents that may be preventing air flow to the oven. This could be causing the oven to work but not heat up properly. If all of these steps are taken and the issue persists, contact Nick’s appliance repair service for assistance.

Share: